| Tube |
A |
B |
Filament |
L |
R |
Socket |
Press |
Notes |
|---|
| 807 | 12 |
1 | 6.3 | 70 |
27 | B | AMPL |
Mut.Cond.3500.Connect plate to top left contact of 6 pin socket. |
| 809 | 8 |
8 | 6.3 | 56 |
0 | A | AMPL |
Mut.Cond.1700.Connect plate cap to right center contact of B socket with lead provided. See note D. |
| 80M | 3 |
7 | 5 | 40 |
0 | A | RECT. STD. |
|
| 80M | 2 |
7 | 5 | 40 |
0 | A | RECT. STD. |
|
| 81 | 2 |
7 | 7.5 | 33 |
0 | A | RECT. STD. |
See note D. |
| 811 | 3 |
2 | 6.3 | 50 |
0 | A | AMPL |
Mut.Cond.1400.Connect cap to upper contact of 5 pin (B) socket. Use special lead provided. |
| 812 | 9 |
2 | 6.3 | 59 |
0 | A | AMPL |
Mut.Cond.2200. See note A. |
| 816 | 7 |
1 | 2.5 | 20 |
0 | A | RECT. STD. |
See notes A and D. |
| 82 | 3 |
7 | 2.5 | 40 |
0 | A | RECT. STD. |
See note D. |
| 82 | 2 |
7 | 2.5 | 40 |
0 | A | RECT. STD. |
See note D. |
| 829/829B | 4 |
2 | 12.6 | 70 |
14 | E | AMPL |
Plate No.2. Use adapter M-418 |
| 829/829B | 7 |
2 | 12.6 | 70 |
14 | E | AMPL |
Plate No.1. Use adapter M-418. |
| 82V | 3 |
7 | 2.5 | 40 |
0 | A | RECT. STD. |
See note D. |
| 82V | 2 |
7 | 2.5 | 40 |
0 | A | RECT. STD. |
See note D. |
| 83 | 3 |
7 | 5 | 40 |
0 | A | RECT. STD. |
See note D. |
| 83 | 2 |
7 | 5 | 40 |
0 | A | RECT. STD. |
See note D. |
| 832/832A | 4 |
2 | 12.6 | 67 |
14 | E | AMPL |
Mut.Cond.3000. Plate No.2. Use adapter M-418 |
| 832/832A | 7 |
2 | 12.6 | 67 |
14 | E | AMPL |
Mut.Cond.3000. Plate No.1. Use adapter M-418 |
| 834 | 10 |
2 | 7.5 | 57 |
0 | A | AMPL |
Mut.Cond.1800. Far cap = Plate. Near cap = grid. See note A. |
| 836 | 7 |
1 | 3 | 30 |
0 | A | RECT. STD. |
See notes A and D. OK over 1500. |
| 837 | 10 |
3 | 12.6 | 71 |
0 | D | AMPL |
See note A. |
| 83V | 3 |
7 | 5 | 40 |
0 | A | RECT. STD. |
See note D. |
| 83V | 2 |
7 | 5 | 40 |
0 | A | RECT. STD. |
See note D. |
| 84 | 5 |
1 | 6.3 | 40 |
0 | B | RECT. STD. |
See note D. |
| 84 | 7 |
7 | 6.3 | 40 |
0 | B | RECT. STD. |
See note D. |
| Important |
|
This I-177 data-base was created using data from I-177 beta 1.08 worksheet, from July 5, 2002.
A great compilation by Nolam E. Lee. |
|
Note A: The plate cap of the tube under test should be connected to the upper left
contact of the 6-pin (C) socket. A 12-inch lead with clip and bananna plug is provided for this purpose. |
|
Note B: Connect the plate cap (nearest the operator) to the upper left contact of the 6-pin (C) socket;
use the lead provided. Connect the grid lead to the remaining cap on the tube. |
|
Note C: Set the MICROMHOS switch at 6000 when testing this section if the tube tester bears either
Order No. 27613-Phila-44-52 or 52346-Phila-45-10 on the nomenclature plate. |
|
Note D: This test is only a partial indication of a good tube. A complete test is only possible
when using equipment. |
|
Note E: Do not tap on this tube when testing for short because damage to the tube may result. |
|
Note F: The Mutual Conductance values listed are averages for new tubes and only for a guide. |
Home
Technical Info
