| Tube |
A |
B |
Filament |
L |
R |
Socket |
Press |
Notes |
|---|
| 89 | 2 |
5 | 6.3 | 54 |
30 | C | AMPL |
Mut.Cond.1550. |
| 89Y | 2 |
5 | 6.3 | 54 |
30 | C | AMPL |
Mut.Cond.1550. |
| 90 | 8 |
6 | 2.5 | 2 |
30 | C | AMPL |
Mut.Cond.500.No.2.Grid. |
| 90 | 8 |
8 | 2.5 | 2 |
30 | C | AMPL |
Mut.Cond.500.No.1.Grid. |
| 9001 | 1 |
9 | 6.3 | 44 |
17 | K | AMPL |
Mut.Cond.1100. Shorts on 4 and 5. |
| 9002 | 2 |
9 | 6.3 | 59 |
18 | L | AMPL |
Mut.Cond.1900. Shorts on 4 and 5. |
| 9003 | 1 |
9 | 6.3 | 54 |
14 | K | AMPL |
Mut Cond.1500. Shorts on 4 and 5. |
| 9004 | 9 |
12 | 6.3 | 44 |
0 | M | DIODE |
Good tube reads in green sector. |
| 9005 | 9 |
1 | 3 | 20 |
0 | M | DIODE |
Shorts on 2, 3, 4, and 5. Good tube reads in green sector. |
| 9006 | 2 |
9 | 6.3 | 20 |
0 | L | DIODE |
Shorts on 4 and 5. |
| 92 | 8 |
6 | 6.3 | 2 |
30 | C | AMPL |
Mut.Cond.500.No.2.Grid. |
| 92 | 8 |
8 | 6.3 | 2 |
30 | C | AMPL |
Mut.Cond.500.No.1 Grid. |
| 95 | 8 |
5 | 2.5 | 57 |
28 | C | AMPL |
Mut.Cond.1750. |
| 950 | 1 |
5 | 2 | 37 |
37 | B | AMPL |
Mut.Cond.950. |
| 951 | 2 |
5 | 2 | 18 |
29 | A | AMPL |
Mut.Cond.640. |
| 954 | 6 |
7 | 6.3 | 44 |
17 | M | AMPL |
Mut.Cond.1100. |
| 955 | 9 |
7 | 6.3 | 59 |
18 | M | AMPL |
Mut.Cond.1900. See note D. |
| 956 | 6 |
7 | 6.3 | 53 |
14 | M | AMPL |
Mut.Cond.1500. |
| 957 | 9 |
7 | 1.1 | 19 |
23 | M | AMPL |
Mut.Cond.650. Shorts on 4 and 5. See note D. |
| 958 | 9 |
7 | 1.1 | 32 |
34 | M | AMPL |
Mut.Cond.1200. Shorts on 4 and 5. See note D. |
| 958A | 9 |
7 | 1.1 | 32 |
34 | M | AMPL |
Shorts on 4 and 5. |
| 959 | 6 |
7 | 1.1 | 10 |
30 | M | AMPL |
Mut.Cond.600. Shorts on 4 and 5. |
| 96 | 1 |
5 | 12.6 | 40 |
0 | A | RECT. STD. |
|
| 98 | 5 |
1 | 6.3 | 40 |
0 | B | RECT. STD. |
Plate Number 2. |
| 98 | 7 |
7 | 6.3 | 40 |
0 | B | RECT. STD. |
Plate Number 1. |
| Important |
|
This I-177 data-base was created using data from I-177 beta 1.08 worksheet, from July 5, 2002.
A great compilation by Nolam E. Lee. |
|
Note A: The plate cap of the tube under test should be connected to the upper left
contact of the 6-pin (C) socket. A 12-inch lead with clip and bananna plug is provided for this purpose. |
|
Note B: Connect the plate cap (nearest the operator) to the upper left contact of the 6-pin (C) socket;
use the lead provided. Connect the grid lead to the remaining cap on the tube. |
|
Note C: Set the MICROMHOS switch at 6000 when testing this section if the tube tester bears either
Order No. 27613-Phila-44-52 or 52346-Phila-45-10 on the nomenclature plate. |
|
Note D: This test is only a partial indication of a good tube. A complete test is only possible
when using equipment. |
|
Note E: Do not tap on this tube when testing for short because damage to the tube may result. |
|
Note F: The Mutual Conductance values listed are averages for new tubes and only for a guide. |
Home
Technical Info
