| Tube |
A |
B |
Filament |
L |
R |
Socket |
Press |
Notes |
|---|
| E90Z | 3 |
5 | 6.3 | 35 |
0 | K | RECT. STD. |
Plate No. 1. See note D. |
| EAA901S | 4 |
2 | 6.3 | 60 |
0 | K | DIODE |
Shorts on 2 and 3. |
| EAA901S | 9 |
2 | 6.3 | 60 |
0 | K | DIODE |
Shorts on 2 and 3. |
| EAA91 | 9 |
2 | 6.3 | 60 |
0 | K | DIODE |
Shorts on 2 and 3. |
| EAA91 | 4 |
2 | 6.3 | 60 |
0 | K | DIODE |
Shorts on 2 and 3. |
| EC90 | 2 |
9 | 6.3 | 67 |
20 | L | AMPL |
Mut.Cond.2200. See note D. |
| ECC801S | 4 |
2 | 12.6 | 15 |
25 | E | AMPL |
Use adapter #6 for triode #2. |
| ECC801S | 4 |
2 | 12.6 | 15 |
25 | E | AMPL |
Use adapter #5 for triode #1. |
| ECC802S | 4 |
2 | 12.6 | 60 |
25 | E | AMPL |
Use adapter #6 for triode #2. |
| ECC802S | 4 |
2 | 12.6 | 60 |
25 | E | AMPL |
Use adapter #5 for triode #1. |
| ECC91 | 11 |
8 | 6.3 | 69 |
11 | K | AMPL |
Mut.Cond.5000. See note D. |
| ECC91 | 1 |
2 | 6.3 | 69 |
11 | K | AMPL |
Mut.Cond.5000. See note D. |
| EL1C | 1 |
5 | 2.5 | 40 |
0 | A | RECT. STD. |
|
| EL1C | 4 |
5 | 2.5 | 40 |
0 | A | RECT. STD. |
|
| FM1000 | 10 |
10 | 6.3 | 53 |
10 | F | AMPL |
Mut.Cond.1500. Grid 2. |
| FM1000 | 3 |
6 | 6.3 | 53 |
10 | F | AMPL |
Mut.Cond.1500. Grid 1. |
| G2S | 5 |
1 | 2.5 | 25 |
0 | B | RECT. STD. |
Plate Number 2. |
| G2S | 7 |
7 | 2.5 | 25 |
0 | B | RECT. STD. |
Plate Number 1. |
| G4S | 5 |
1 | 2.5 | 25 |
0 | B | RECT. STD. |
Plate Number 2. |
| G4S | 7 |
7 | 2.5 | 25 |
0 | B | RECT. STD. |
Plate Number 1. |
| G84 | 2 |
7 | 2.5 | 40 |
0 | A | RECT. STD. |
|
| GA | 1 |
5 | 5 | 60 |
16 | ? | AMPL |
Mut.Cond.2000. |
| GU12 (Brit.) | 7 |
1 | 2.5 | 40 |
0 | A | RECT. STD. |
See notes A and D. |
| H2-10 | 7 |
1 | 2.5 | 0 |
0 | A | RECT. STD. |
OK over 1000. See notes A and D. |
| HA2 | 9 |
7 | 6.3 | 59 |
18 | M | AMPL |
Mut.Cond.1900. See note D. |
| Important |
|
This I-177 data-base was created using data from I-177 beta 1.08 worksheet, from July 5, 2002.
A great compilation by Nolam E. Lee. |
|
Note A: The plate cap of the tube under test should be connected to the upper left
contact of the 6-pin (C) socket. A 12-inch lead with clip and bananna plug is provided for this purpose. |
|
Note B: Connect the plate cap (nearest the operator) to the upper left contact of the 6-pin (C) socket;
use the lead provided. Connect the grid lead to the remaining cap on the tube. |
|
Note C: Set the MICROMHOS switch at 6000 when testing this section if the tube tester bears either
Order No. 27613-Phila-44-52 or 52346-Phila-45-10 on the nomenclature plate. |
|
Note D: This test is only a partial indication of a good tube. A complete test is only possible
when using equipment. |
|
Note E: Do not tap on this tube when testing for short because damage to the tube may result. |
|
Note F: The Mutual Conductance values listed are averages for new tubes and only for a guide. |
Home
Technical Info
