| Tube |
A |
B |
Filament |
L |
R |
Socket |
Press |
Notes |
|---|
| 313C | 2 |
10 | 50 | 0 |
0 | A | DIODE |
Good tube gives meter reading. May read in red sector. See note D. |
| 313CC | 2 |
10 | 50 | 0 |
0 | A | DIODE |
Good tube gives meter reading. May read in red sector. See note D. |
| 313CD | 2 |
10 | 50 | 0 |
0 | A | DIODE |
Good tube gives meter reading. May read in red sector. See note D. |
| 32 | 2 |
5 | 2 | 19 |
30 | A | AMPL |
Mut.Cond.640. |
| 328A | 8 |
5 | 7.5 | 54 |
16 | C | AMPL |
|
| 329A | 7 |
6 | 7.5 | 62 |
33 | B | AMPL |
|
| 32L7 | 11 |
5 | 35 | 40 |
0 | E | RECT. STD. |
See note D. |
| 32L7 | 8 |
5 | 35 | 71 |
18 | E | AMPL |
Mut.Cond.4800. |
| 32L7 | 11 |
5 | 35 | 0 |
0 | E | NOTHING |
Test for shorts. |
| 33 | 1 |
5 | 2 | 50 |
29 | B | AMPL |
Mut.Cond.1450. |
| 336A | 8 |
5 | 10 | 60 |
20 | C | AMPL |
Allow tube 60 seconds to warm up. Set MICROMHOS switch at 6000. OK over 750. |
| 337A | 2 |
5 | 10 | 50 |
16 | C | AMPL |
|
| 338A | 1 |
6 | 10 | 40 |
80 | B | RECT. STD. |
Tube strikes at approximately 35 on R when this control is turned counterclockwise. See note D. |
| 339A | 12 |
1 | 5 | 60 |
45 | B | AMPL |
Set MICROMHOS switch to 6000. OK over 1250. See notes A and D. |
| 34 | 2 |
5 | 2 | 14 |
27 | A | AMPL |
Mut.Cond.600. |
| 345A | 7 |
7 | 6.3 | 40 |
0 | B | RECT. STD. |
Allow tube 60 seconds to warm up. See note D. |
| 345A | 4 |
3 | 6.3 | 40 |
0 | B | RECT. STD. |
Allow tube 60 seconds to warm up. See note D. |
| 348A | 1 |
9 | 6.3 | 48 |
18 | E | AMPL |
|
| 349A | 8 |
5 | 6.3 | 67 |
30 | E | AMPL |
|
| 35 | 7 |
6 | 2.5 | 42 |
20 | B | AMPL |
Mut.Cond.1020. |
| 350A | 12 |
1 | 6.3 | 73 |
27 | B | AMPL |
See note A. |
| 350B | 8 |
5 | 6.3 | 73 |
27 | E | AMPL |
|
| 352A | 10 |
3 | 10 | 0 |
0 | C | DIODE |
|
| 352A | 10 |
6 | 10 | 0 |
0 | C | DIODE |
|
| 352A | 7 |
6 | 10 | 28 |
20 | C | AMPL |
|
| Important |
|
This I-177 data-base was created using data from I-177 beta 1.08 worksheet, from July 5, 2002.
A great compilation by Nolam E. Lee. |
|
Note A: The plate cap of the tube under test should be connected to the upper left
contact of the 6-pin (C) socket. A 12-inch lead with clip and bananna plug is provided for this purpose. |
|
Note B: Connect the plate cap (nearest the operator) to the upper left contact of the 6-pin (C) socket;
use the lead provided. Connect the grid lead to the remaining cap on the tube. |
|
Note C: Set the MICROMHOS switch at 6000 when testing this section if the tube tester bears either
Order No. 27613-Phila-44-52 or 52346-Phila-45-10 on the nomenclature plate. |
|
Note D: This test is only a partial indication of a good tube. A complete test is only possible
when using equipment. |
|
Note E: Do not tap on this tube when testing for short because damage to the tube may result. |
|
Note F: The Mutual Conductance values listed are averages for new tubes and only for a guide. |
Home
Technical Info
