| Tube |
A |
B |
Filament |
L |
R |
Socket |
Press |
Notes |
|---|
| 35A5 | 6 |
2 | 35 | 74 |
27 | F | AMPL |
Mut.Cond.5900. |
| 35B5 | 8 |
5 | 35 | 70 |
28 | L | AMPL |
Mut.Cond.4500. |
| 35L6 | 8 |
5 | 35 | 71 |
32 | E | AMPL |
Mut.Cond.5800. |
| 35S | 7 |
6 | 2.5 | 42 |
20 | B | AMPL |
Mut.Cond.1020. |
| 35W4 | 1 |
5 | 35 | 40 |
0 | L | RECT. STD. |
Shorts on 4 and 5. See note D. |
| 35W4 | 1 |
5 | 0 | 0 |
0 | L | NOTHING |
Shorts on 1, 2, 3, 4, and 5. |
| 35Y4 | 1 |
1 | 35 | 40 |
0 | F | RECT. STD. |
See note D. |
| 35Y4 | 3 |
4 | 0 | 0 |
0 | F | NOTHING |
Shorts on 1, 2, 3, 4, and 5. |
| 35Z3 | 1 |
1 | 35 | 35 |
0 | F | RECT. STD. |
See note D. |
| 35Z4 | 10 |
2 | 35 | 40 |
0 | E | RECT. STD. |
See note D. |
| 35Z5 | 11 |
1 | 35 | 40 |
0 | E | RECT. STD. |
See note D. |
| 35Z5 | 1 |
3 | 0 | 40 |
0 | E | NOTHING |
Shorts on 1, 2, 3, 4, and 5. |
| 35Z6 | 7 |
5 | 35 | 40 |
0 | E | RECT. STD. |
See note D. |
| 35Z6 | 7 |
2 | 35 | 40 |
0 | E | RECT. STD. |
See note D. |
| 36 | 7 |
6 | 6.3 | 43 |
20 | B | AMPL |
Mut.Cond.1050. |
| 37 | 1 |
6 | 6.3 | 36 |
34 | B | AMPL |
Mut.Cond.900. |
| 38 | 7 |
6 | 6.3 | 41 |
32 | B | AMPL |
Mut.Cond.1050. |
| 38001 | 2 |
10 | 5 | 26 |
39 | A | AMPL |
Mut.Cond.725. |
| 38019 | 11 |
6 | 2 | 42 |
12 | C | AMPL |
Mut.Cond.1000. |
| 38019 | 8 |
8 | 2 | 42 |
12 | C | AMPL |
Mut.Cond.1000. |
| 38022 | 2 |
5 | 3 | 0 |
37 | A | AMPL |
Mut.Cond.500. |
| 38024 | 7 |
6 | 2.5 | 42 |
10 | B | AMPL |
Mut.Cond.1000. |
| 38027 | 1 |
6 | 2.5 | 40 |
34 | B | AMPL |
Mut.Cond.1000. |
| 38030 | 2 |
10 | 2 | 36 |
33 | A | AMPL |
Mut.Cond.900. |
| 38031 | 2 |
10 | 2 | 35 |
53 | A | AMPL |
Mut.Cond.925. |
| Important |
|
This I-177 data-base was created using data from I-177 beta 1.08 worksheet, from July 5, 2002.
A great compilation by Nolam E. Lee. |
|
Note A: The plate cap of the tube under test should be connected to the upper left
contact of the 6-pin (C) socket. A 12-inch lead with clip and bananna plug is provided for this purpose. |
|
Note B: Connect the plate cap (nearest the operator) to the upper left contact of the 6-pin (C) socket;
use the lead provided. Connect the grid lead to the remaining cap on the tube. |
|
Note C: Set the MICROMHOS switch at 6000 when testing this section if the tube tester bears either
Order No. 27613-Phila-44-52 or 52346-Phila-45-10 on the nomenclature plate. |
|
Note D: This test is only a partial indication of a good tube. A complete test is only possible
when using equipment. |
|
Note E: Do not tap on this tube when testing for short because damage to the tube may result. |
|
Note F: The Mutual Conductance values listed are averages for new tubes and only for a guide. |
Home
Technical Info
