| Tube |
A |
B |
Filament |
L |
R |
Socket |
Press |
Notes |
|---|
| 38568K | 11 |
5 | 6.3 | 63 |
9 | E | AMPL |
Mut.Cond.2400. See note D. |
| 38568K | 8 |
5 | 6.3 | 41 |
9 | E | AMPL |
Mut.Cond.1000. See note D. |
| 38593 | 3 |
7 | 5 | 40 |
0 | A | RECT. STD. |
See note D. |
| 38593 | 2 |
7 | 5 | 40 |
0 | A | RECT. STD. |
See note D. |
| 38616 | 12 |
5 | 6.3 | 53 |
10 | D | AMPL |
Mut.Cond.1500. |
| 38616 | 1 |
5 | 6.3 | 53 |
10 | D | AMPL |
Mut.Cond.1500. |
| 38617 | 10 |
6 | 6.3 | 60 |
25 | D | AMPL |
Mut.Cond.400. OK over 320. See note D. |
| 38617 | 7 |
6 | 6.3 | 41 |
18 | D | AMPL |
Mut.Cond.1000. See note D. |
| 38627 | 10 |
3 | 6.3 | 0 |
0 | D | DIODE |
|
| 38627 | 10 |
6 | 6.3 | 0 |
0 | D | DIODE |
|
| 38627 | 7 |
6 | 6.3 | 41 |
25 | D | AMPL |
Mut.Cond.1000. |
| 38636 | 1 |
7 | 6.3 | 49 |
17 | C | AMPL |
Mut.Cond.1225. |
| 38646 | 1 |
7 | 6.3 | 56 |
17 | C | AMPL |
Mut.Cond.1600. |
| 38655 | 12 |
2 | 6.3 | 0 |
0 | C | AMPL |
Eye closed. |
| 38655 | 12 |
3 | 6.3 | 0 |
0 | C | AMPL |
Eye open. |
| 38667 | 10 |
6 | 6.3 | 60 |
23 | D | AMPL |
Mut.Cond.450. OK over 360. |
| 38667 | 7 |
6 | 6.3 | 45 |
23 | D | AMPL |
Mut.Cond.1100. |
| 38717E | 8 |
8 | 2 | 45 |
17 | E | AMPL |
Mut.Cond.1150. |
| 38717E | 11 |
6 | 2 | 45 |
17 | E | AMPL |
Mut.Cond.1150. |
| 38765J | 7 |
5 | 6.3 | 60 |
24 | E | AMPL |
Mut.Cond.2000. |
| 38766Y | 8 |
5 | 6.3 | 60 |
42 | E | AMPL |
Set MICROMHOS switch at 6000. |
| 38768F | 11 |
7 | 6.3 | 60 |
13 | E | AMPL |
Mut.Cond.2000. Plate No. 2. |
| 38768F | 8 |
7 | 6.3 | 60 |
13 | E | AMPL |
Mut.Cond.2000. Plate No. 1. |
| 38807 | 12 |
1 | 6.3 | 70 |
27 | B | AMPL |
Mut.Cond. 3500. Connect plate to top left contact of 6 pin socket. |
| 38837 | 10 |
3 | 12.6 | 71 |
0 | D | AMPL |
See note A. |
| Important |
|
This I-177 data-base was created using data from I-177 beta 1.08 worksheet, from July 5, 2002.
A great compilation by Nolam E. Lee. |
|
Note A: The plate cap of the tube under test should be connected to the upper left
contact of the 6-pin (C) socket. A 12-inch lead with clip and bananna plug is provided for this purpose. |
|
Note B: Connect the plate cap (nearest the operator) to the upper left contact of the 6-pin (C) socket;
use the lead provided. Connect the grid lead to the remaining cap on the tube. |
|
Note C: Set the MICROMHOS switch at 6000 when testing this section if the tube tester bears either
Order No. 27613-Phila-44-52 or 52346-Phila-45-10 on the nomenclature plate. |
|
Note D: This test is only a partial indication of a good tube. A complete test is only possible
when using equipment. |
|
Note E: Do not tap on this tube when testing for short because damage to the tube may result. |
|
Note F: The Mutual Conductance values listed are averages for new tubes and only for a guide. |
Home
Technical Info
