| Tube |
A |
B |
Filament |
L |
R |
Socket |
Press |
Notes |
|---|
| 3B22 | 1 |
5 | 2.5 | 40 |
0 | A | RECT. STD. |
|
| 3B22 | 4 |
5 | 2.5 | 40 |
0 | A | RECT. STD. |
|
| 3B23 | 10 |
4 | 2.5 | 55 |
0 | A | DIODE |
Connect tube cap away from operator. See notes A and D. |
| 3B23 | 10 |
4 | 2.5 | 55 |
0 | A | DIODE |
Connect tube cap nearest operator. See notes A and D. |
| 3B24 | 7 |
1 | 2.5 | 5 |
0 | A | RECT. STD. |
Shorts on 4 and 5. See notes A and D. |
| 3B26 | 7 |
2 | 2.5 | 20 |
0 | E | DIODE |
See notes A and D. |
| 3B28 | 7 |
1 | 2.5 | 40 |
0 | A | RECT. STD. |
See notes A and D. |
| 3B29 | 7 |
2 | 2.5 | 20 |
0 | A | DIODE |
See notes A and D. |
| 3B5GT | 8 |
5 | 2.5 | 54 |
49 | E | AMPL |
Mut.Cond.1500. Shorts on 4 and 5. |
| 3B7 | 6 |
6 | 2.5 | 35 |
25 | F | DIODE |
Shorts on 4 and 5. Plate No. 1. Reads in Green Sector |
| 3B7 | 1 |
6 | 2.5 | 35 |
25 | F | DIODE |
Shorts on 4 and 5. Plate No. 2. Reads in Green Sector |
| 3BA6 | 7 |
9 | 3 | 70 |
0 | K | AMPL |
Mut.Cond.4300. |
| 3BC5 | 7 |
9 | 3 | 55 |
19 | K | AMPL |
Mut.Cond.1600. Shorts on 4 and 5. |
| 3BE6 | 7 |
9 | 3 | 55 |
23 | K | AMPL |
Mut.Cond.1600. |
| 3BN6 | 10 |
4 | 3 | 0 |
0 | K | AMPL |
Mut.Cond.500. |
| 3BY6 | 4 |
9 | 3 | 47 |
28 | K | AMPL |
Mut.Cond.1200. |
| 3BZ6 | 1 |
9 | 3 | 64 |
17 | K | AMPL |
Mut.Cond.2500. |
| 3C23 | 9 |
2 | 3 | 40 |
80 | A | RECT. STD. |
Tube strikes at approximately 26 when R control is rotated counterclockwise. See notes A and D. |
| 3C24 | 3 |
2 | 6.3 | 30 |
20 | A | AMPL |
Connect top terminal of tube under test to upper contact of 5 pin (B) socket. Use separate lead provided. Connect side t |
| 3CB6 | 1 |
9 | 3 | 62 |
18 | K | AMPL |
Mut.Cond.2200. |
| 3CF6 | 1 |
9 | 3 | 62 |
18 | K | AMPL |
Mut.Cond.2200. |
| 3CS6 | 4 |
9 | 3 | 30 |
33 | K | AMPL |
Mut.Cond.800. |
| 3D6 | 6 |
2 | 2.5 | 61 |
30 | F | AMPL |
Mut.Cond.2100. Shorts on 1. See note E. |
| 3E29 | 4 |
2 | 12.6 | 70 |
14 | E | AMPL |
Plate No. 2. Use Adapter M-418. |
| 3E29 | 7 |
2 | 12.6 | 70 |
14 | E | AMPL |
Plate No. 1. Use Adapter M-418. |
| Important |
|
This I-177 data-base was created using data from I-177 beta 1.08 worksheet, from July 5, 2002.
A great compilation by Nolam E. Lee. |
|
Note A: The plate cap of the tube under test should be connected to the upper left
contact of the 6-pin (C) socket. A 12-inch lead with clip and bananna plug is provided for this purpose. |
|
Note B: Connect the plate cap (nearest the operator) to the upper left contact of the 6-pin (C) socket;
use the lead provided. Connect the grid lead to the remaining cap on the tube. |
|
Note C: Set the MICROMHOS switch at 6000 when testing this section if the tube tester bears either
Order No. 27613-Phila-44-52 or 52346-Phila-45-10 on the nomenclature plate. |
|
Note D: This test is only a partial indication of a good tube. A complete test is only possible
when using equipment. |
|
Note E: Do not tap on this tube when testing for short because damage to the tube may result. |
|
Note F: The Mutual Conductance values listed are averages for new tubes and only for a guide. |
Home
Technical Info
