| Tube |
A |
B |
Filament |
L |
R |
Socket |
Press |
Notes |
|---|
| 69 | 8 |
6 | 6.3 | 0 |
19 | B | AMPL |
Mut.Cond.500. No. 2. Grid. |
| 69 | 8 |
8 | 6.3 | 0 |
19 | B | AMPL |
Mut.Cond.500. No. 1. Grid. |
| 6A3 | 2 |
10 | 6.3 | 67 |
55 | A | AMPL |
Mut.Cond.3000. |
| 6A4 | 1 |
5 | 6.3 | 60 |
23 | B | AMPL |
Mut.Cond.3000. |
| 6A4/LA | 1 |
5 | 6.3 | 60 |
23 | B | AMPL |
Mut.Cont.3000. |
| 6A5G | 7 |
5 | 6.3 | 67 |
55 | E | AMPL |
Mut.Cond.3000. Shorts on 4 and 5 |
| 6A6 | 12 |
5 | 6.3 | 53 |
10 | D | AMPL |
Mut.Cond.1500. |
| 6A6 | 1 |
5 | 6.3 | 53 |
10 | D | AMPL |
Mut.Cond.1500. |
| 6A7 | 10 |
6 | 6.3 | 60 |
25 | D | AMPL |
Mut.Cond.400. OK over 320. See note D. |
| 6A7 | 7 |
6 | 6.3 | 41 |
18 | D | AMPL |
Mut.Cond.1000. See note D. |
| 6A8 | 12 |
7 | 6.3 | 60 |
30 | E | AMPL |
Mut.Cond.300. OK over 240. See note D. |
| 6A8 | 7 |
7 | 6.3 | 41 |
18 | E | AMPL |
Mut.Cond.1000. See note D. |
| 6AB4 | 11 |
9 | 6.3 | 70 |
8 | K | AMPL |
Mut.Cond.4000. |
| 6AB5 | 12 |
2 | 6.3 | 0 |
0 | C | AMPL |
Eye closed. |
| 6AB5 | 12 |
3 | 6.3 | 0 |
0 | C | AMPL |
Eye open. |
| 6AB6 | 8 |
5 | 6.3 | 53 |
0 | E | AMPL |
Mut.Cond.1450. |
| 6AB7 | 4 |
2 | 6.3 | 69 |
8 | E | AMPL |
Mut.Cond.3500. |
| 6AC5 | 8 |
5 | 6.3 | 40 |
0 | E | AMPL |
Mut.Cond.1000. |
| 6AC6 | 8 |
5 | 6.3 | 63 |
0 | E | AMPL |
Mut.Cond.2400. |
| 6AC7 | 4 |
2 | 6.3 | 71 |
10 | E | AMPL |
Mut.Cond.3500. |
| 6AD5 | 7 |
5 | 6.3 | 43 |
10 | E | AMPL |
Mut.Cond.1000. |
| 6AD6 | 3 |
8 | 6.3 | 0 |
0 | E | AMPL |
Eye no.2 open. Eye No.1 closed. |
| 6AD6 | 2 |
8 | 6.3 | 0 |
0 | E | AMPL |
Eye No.1 open. Eye No.2 closed. |
| 6AD7 | 5 |
5 | 6.3 | 60 |
65 | E | DIODE |
Mut.Cond.325. OK over 260. |
| 6AD7 | 8 |
5 | 6.3 | 60 |
24 | E | AMPL |
Mut.Cond.2000. |
| Important |
|
This I-177 data-base was created using data from I-177 beta 1.08 worksheet, from July 5, 2002.
A great compilation by Nolam E. Lee. |
|
Note A: The plate cap of the tube under test should be connected to the upper left
contact of the 6-pin (C) socket. A 12-inch lead with clip and bananna plug is provided for this purpose. |
|
Note B: Connect the plate cap (nearest the operator) to the upper left contact of the 6-pin (C) socket;
use the lead provided. Connect the grid lead to the remaining cap on the tube. |
|
Note C: Set the MICROMHOS switch at 6000 when testing this section if the tube tester bears either
Order No. 27613-Phila-44-52 or 52346-Phila-45-10 on the nomenclature plate. |
|
Note D: This test is only a partial indication of a good tube. A complete test is only possible
when using equipment. |
|
Note E: Do not tap on this tube when testing for short because damage to the tube may result. |
|
Note F: The Mutual Conductance values listed are averages for new tubes and only for a guide. |
Home
Technical Info
