| Tube |
A |
B |
Filament |
L |
R |
Socket |
Press |
Notes |
|---|
| 6202 | 3 |
5 | 6.3 | 33 |
0 | K | RECT. STD. |
Plate No.1. |
| 6265 | 1 |
9 | 6.3 | 60 |
12 | K | AMPL |
Mut.Cond.2000. |
| 64/64A | 7 |
6 | 6.3 | 42 |
26 | B | AMPL |
Mut.Cond.1050. |
| 6485 | 7 |
9 | 6.3 | 68 |
15 | K | AMPL |
Mut.Cond.5000. |
| 65/65A | 7 |
6 | 6.3 | 41 |
23 | B | AMPL |
Mut.Cond.1000. |
| 6626 | 4 |
4 | 0 | 0 |
0 | H | GAS No. 1 |
OK over 200. Shorts on 4 and 5. See note D. |
| 6627 | 4 |
4 | 0 | 30 |
0 | H | GAS No. 1 |
OK over 200. Shorts on 4 and 5. See note D. |
| 6660 | 7 |
9 | 6.3 | 70 |
0 | K | AMPL |
Mut.Cond.4300. |
| 6661 | 1 |
9 | 6.3 | 60 |
12 | A | AMPL |
Mut.Cond.2000. |
| 6662 | 7 |
9 | 6.3 | 70 |
10 | K | AMPL |
Mut.Cond.3800. |
| 6663 | 4 |
2 | 6.3 | 60 |
0 | K | DIODE |
Shorts on 2 and 3. |
| 6663 | 9 |
2 | 6.3 | 60 |
0 | K | DIODE |
Shorts on 2 and 3. |
| 6664 | 11 |
9 | 6.3 | 70 |
8 | K | AMPL |
Mut.Cond.4000. |
| 6669 | 8 |
5 | 6.3 | 70 |
17 | L | AMPL |
Mut.Cond.3700. |
| 6670 | 4 |
2 | 12.6 | 60 |
25 | E | AMPL |
Use adapter #6 for triode #2. |
| 6670 | 4 |
2 | 12.6 | 60 |
25 | E | AMPL |
Use adapter #5 for triode #1. |
| 6671 | 4 |
2 | 12.6 | 15 |
25 | E | AMPL |
Use adapter #6 for triode #2. |
| 6671 | 4 |
2 | 12.6 | 15 |
25 | E | AMPL |
Use adapter #5 for triode #1. |
| 6676 | 1 |
9 | 6.3 | 62 |
18 | K | AMPL |
Mut.Cond.2200. |
| 6679 | 4 |
2 | 12.6 | 15 |
25 | E | AMPL |
Use adapter #6 for triode #2. |
| 6679 | 4 |
2 | 12.6 | 15 |
25 | E | AMPL |
Use adapter #5 for triode #1. |
| 6680 | 4 |
2 | 12.6 | 60 |
25 | E | AMPL |
Use adapter #6 for triode #2. |
| 6680 | 4 |
2 | 12.6 | 60 |
25 | E | AMPL |
Use adapter #5 for triode #1. |
| 67/67A | 1 |
6 | 6.3 | 40 |
34 | B | AMPL |
Mut.Cond.1000. |
| 68/68A | 7 |
6 | 6.3 | 41 |
32 | B | AMPL |
Mut.Cond.1050. |
| Important |
|
This I-177 data-base was created using data from I-177 beta 1.08 worksheet, from July 5, 2002.
A great compilation by Nolam E. Lee. |
|
Note A: The plate cap of the tube under test should be connected to the upper left
contact of the 6-pin (C) socket. A 12-inch lead with clip and bananna plug is provided for this purpose. |
|
Note B: Connect the plate cap (nearest the operator) to the upper left contact of the 6-pin (C) socket;
use the lead provided. Connect the grid lead to the remaining cap on the tube. |
|
Note C: Set the MICROMHOS switch at 6000 when testing this section if the tube tester bears either
Order No. 27613-Phila-44-52 or 52346-Phila-45-10 on the nomenclature plate. |
|
Note D: This test is only a partial indication of a good tube. A complete test is only possible
when using equipment. |
|
Note E: Do not tap on this tube when testing for short because damage to the tube may result. |
|
Note F: The Mutual Conductance values listed are averages for new tubes and only for a guide. |
Home
Technical Info
