| Tube |
A |
B |
Filament |
L |
R |
Socket |
Press |
Notes |
|---|
| 6095 | 8 |
5 | 6.3 | 70 |
17 | L | AMPL |
|
| 6096 | 1 |
9 | 6.3 | 55 |
20 | K | AMPL |
Mut.Cond.1500.Shorts on 4 and 5. |
| 6097 | 4 |
2 | 6.3 | 60 |
0 | K | DIODE |
Shorts on 2 and 3. |
| 6097 | 9 |
2 | 6.3 | 60 |
0 | K | DIODE |
Shorts on 2 and 3. |
| 6098 | 8 |
5 | 6.3 | 71 |
36 | E | AMPL |
Use Adapter # 3. |
| 6099 | 11 |
8 | 6.3 | 69 |
11 | K | AMPL |
Mut.Cond.5000. See note D. |
| 6099 | 1 |
2 | 6.3 | 69 |
11 | K | AMPL |
Mut.Cond.5000. See note D. |
| 6100 | 2 |
9 | 6.3 | 67 |
20 | L | AMPL |
See note D. |
| 6101 | 11 |
8 | 6.3 | 69 |
11 | K | AMPL |
See note D. |
| 6101 | 1 |
2 | 6.3 | 69 |
11 | K | AMPL |
See note D. |
| 6113 | 10 |
4 | 6.3 | 53 |
0 | G | AMPL |
Mut.Cond.1400. Shorts on 2 and 3. |
| 6113 | 4 |
1 | 6.3 | 36 |
0 | G | AMPL |
Mut.Cond.900. |
| 6134 | 4 |
2 | 6.3 | 71 |
10 | E | AMPL |
Mut.Cond.3500. |
| 6135 | 2 |
9 | 6.3 | 62 |
28 | L | AMPL |
Mut.Cond.2200. |
| 6136 | 1 |
9 | 6.3 | 62 |
18 | K | AMPL |
Mut.Cond.2300 |
| 6137 | 4 |
2 | 6.3 | 59 |
18 | E | AMPL |
Mut.Cond.1900. |
| 6145 | 5 |
4 | 6.3 | 74 |
8 | F | AMPL |
|
| 615 | 7 |
5 | 6.3 | 36 |
25 | E | AMPL |
Connect right cap to upper right contact on A socket with lead provided. Connect grid lead to left cap. |
| 6186 | 1 |
9 | 6.3 | 67 |
0 | K | AMPL |
Mut.Cond.3000. Shorts on 4 and 5 |
| 6187 | 1 |
9 | 6.3 | 42 |
15 | K | AMPL |
|
| 6189 | 4 |
2 | 12.6 | 60 |
25 | E | AMPL |
Use adapter #6 for triode #2. |
| 6189 | 4 |
2 | 12.6 | 60 |
25 | E | AMPL |
Use adapter #5 for triode #1. |
| 6201 | 4 |
2 | 12.6 | 15 |
25 | E | AMPL |
Use adapter #6 for triode #2. |
| 6201 | 4 |
2 | 12.6 | 15 |
25 | E | AMPL |
Use adapter #5 for triode #1. |
| 6202 | 6 |
5 | 6.3 | 33 |
0 | K | RECT. STD. |
Plate No.2. |
| Important |
|
This I-177 data-base was created using data from I-177 beta 1.08 worksheet, from July 5, 2002.
A great compilation by Nolam E. Lee. |
|
Note A: The plate cap of the tube under test should be connected to the upper left
contact of the 6-pin (C) socket. A 12-inch lead with clip and bananna plug is provided for this purpose. |
|
Note B: Connect the plate cap (nearest the operator) to the upper left contact of the 6-pin (C) socket;
use the lead provided. Connect the grid lead to the remaining cap on the tube. |
|
Note C: Set the MICROMHOS switch at 6000 when testing this section if the tube tester bears either
Order No. 27613-Phila-44-52 or 52346-Phila-45-10 on the nomenclature plate. |
|
Note D: This test is only a partial indication of a good tube. A complete test is only possible
when using equipment. |
|
Note E: Do not tap on this tube when testing for short because damage to the tube may result. |
|
Note F: The Mutual Conductance values listed are averages for new tubes and only for a guide. |
Home
Technical Info
